Photographing paintings without glare

You want to photograph a painting, and there is always a bright spot or a shiny streak on the paint. Almost always the cause is the angle of the light, not the camera. A rule for the lighting angle and a simple test solve most cases. For the rest there is the polarising filter. The full routine for a shoot is in the guide Photographing artworks: how to get good photos of your work.

Updated 17 October 2026.

Why a painting reflects

Light bounces off a smooth surface like a ball off a wall. It leaves at the same angle at which it arrives. If the light comes from the camera, it bounces straight back into the lens. If it comes at an angle from the side, it flies off to the other side.

Oil paint, acrylic, gloss medium and varnish all shine. Varnish is the clear protective layer on a finished painting. Thick paint also forms tiny ridges and peaks. Their sloping sides face in many directions, and some of them almost always throw light towards the camera. That is why heavy brushstrokes often still shine when the smooth areas are already calm.

The rule for the lighting angle

Place two identical lamps to the left and right of the painting. Each one points at the centre at about 45 degrees. The camera stands exactly in the middle, further back than the lamps. Paul Bourke lit oil paintings for very detailed captures at the same angle. He set up a large, flat light at 45 degrees to the direction the camera looks in (source 1).

View from above

  ┌──────────────── Painting ───────────────┐
  └────────────────────┬────────────────────┘
                     ╱ │ ╲
                   ╱   │   ╲
                 ╱ 45° │ 45° ╲
               ╱       │       ╲
         [Lamp left]   │   [Lamp right]
                       │
                   [Camera]
What you setHow to set it
Angle of the lampsabout 45 degrees to the painting, both the same
Distance of the lampsboth equally far away, measured with a tape
Height of the lampsthe centre of each lamp level with the centre of the painting
Camera positionexactly in front of the centre, parallel to the painting
Other lightoff, including the ceiling light, curtains closed

If it still shines, move the lamps further to the side. The light then strikes the painting at a flatter angle. If one side gets darker, move both lamps further away. The further away they are, the more evenly the surface is lit.

The mirror test

A small pocket mirror tells you before the first shot whether the painting will reflect. Hold it flat against the centre of the painting and look into it from the camera position. If you see a lamp in it, its light will also reach the photo. If you only see the dark ceiling or the room, the angle is right. Then check the four corners as well.

Polarising filters and cross polarisation

A polarising filter is a rotating filter in front of the lens. It only lets through light that vibrates in one particular direction. A polariser on the lens alone only partly reduces reflections on paint.

Cross polarisation is more reliable. A sheet of polarising film goes in front of each lamp and aligns its light in one direction. Bourke specifies linear film, which makes the light vibrate in exactly one direction. He rules out circular film, in which the light vibrates in a spiral (source 1). You then turn the polariser on the lens 90 degrees against it. Shiny spots send the light back in the same direction of vibration, and the turned filter blocks almost all of it. Matte paint jumbles the direction of vibration, so its light gets through (source 1).

To line it up, hold a shiny metal spoon in front of the camera. Watch the camera screen that shows the picture before you take it. Then turn the filter on the lens until the bright highlight on the spoon disappears (source 1).

The method costs light. Bourke gives at least 1.3 stops (source 1). One stop halves the light.

Worked exampleValue
Shutter speed without filter1/30 second
Loss according to Bourkeat least 1.3 stops
Factor for the time, rounded2.5
Shutter speed with filterabout 1/12 second

At speeds this slow you need a tripod. Without any shine at all, thick oil paint can look flat. If in doubt, take one photo with the filter and one without, and decide on screen.

Faults, causes and fixes

What you see in the photoCauseFix
a bright spot in the centrethe light comes from the camera, for example the flashflash off, light from both sides
shiny streaks on the brushstrokesthick paint throws light in many directionsset the lamps at a flatter angle, or use cross polarisation
one half of the picture is brighterthe lamps are at different distances or of different strengthmeasure the distance, use two identical lamps
the edges are brighter than the centrethe lamps are too closemove both lamps further away
a window or you yourself in the pictureglass in front of the work reflects the roomphotograph the work without glass, otherwise darken the room and hold black card with a hole in front of the camera
one colour shines even on smooth areassome pigments are glossier by nature, in Bourke's case the blue of a sky (source 1)cross polarisation

Cut a hole for the lens in the centre of the black card. The glass will then reflect only black.

A work shown large on the website with all its details, shown with a public-domain work.

Sources

  1. Paul Bourke, "Cross polarisation in photography", October 2022, retrieved 17 October 2026: https://paulbourke.net/miscellaneous/crosspolarisation/